- 您现在的位置：买卖IC网 > Sheet目录299 > 71M6543F-IGT/F (Maxim Integrated Products)IC ENERGY METERING
71M6543F/71M6543G Data Sheet
If TEMP_PWR selects VBAT_RTC when the battery is nearly discharged, the temperature measurement
may not finish. In this case, firmware may complete the measurement by selecting V3P3D
( TEMP_PWR = 1).
Table 45: I/O RAM Registers for Temperature and Battery Measurement
Name
TBYTE_BUSY
Location
28A0[3]
Rst
0
Wk
0
Dir
R
Description
Indicates that hardware is still writing the 0x28A0
byte. Additional writes to this byte are locked out
while it is one. Write duration could be as long as 6 ms.
Sets the period between temperature measurements.
Automatic measurements can be enabled in any
mode (MSN, BRN, LCD, or SLP).
TEMP_PER[2:0]
28A0[2:0]
0
–
R/W
TEMP_PER
0
Time
Manual updates (see TEMP_START )
1-6
7
2 ^ (3+ TEMP_PER ) (seconds)
Continuous
TEMP_BAT
TEMP_START
TEMP_PWR
TEMP_BSEL
28A0[4]
28B4[6]
28A0[6]
28A0[7]
0
0
0
0
–
–
–
–
R/W
R/W
R/W
R/W
Causes VBAT to be measured whenever a
temperature measurement is performed.
TEMP_PER[2:0] must be zero in order for TEMP_START
to function. If TEMP_PER[2:0] = 0, then setting
TEMP_START starts a temperature measurement.
Ignored in SLP and LCD modes. Hardware clears
TEMP_START when the temperature measurement is
complete.
Selects the power source for the temperature sensor:
1 = V3P3D, 0 = VBAT_RTC. This bit is ignored in
SLP and LCD modes, where the temperature sensor is
always powered by VBAT_RTC.
Selects which battery is monitored by the
temperature sensor: 1 = VBAT, 0 = VBAT_RTC
TEMP_TEST[1:0] 2500[1:0]
0
–
R/W
Test bits for the temperature monitor VCO.
TEMP_TEST must be 00 in regular operation. Any
other value causes the VCO to run continuously with
the control voltage described below.
TEMP_TEST Function
00
01
1X
Normal operation
Reserved for factory test
Reserved for factory test
STEMP[10:3]
STEMP[2:0]
2881[7:0]
2882[7:5]
R
R
The result of the temperature measurement.
The STEMP[10:0] value may be obtained in C with a
single 16-bit read and divide by 32 operation as
follows:
volatile int16_t xdata STEMP _at_0x2881;
fa = (float)(STEMP/32);
BSENSE[7:0]
BCURR
2885[7:0]
2704[3]
–
0
–
0
R
R/W
The result of the battery measurement.
Connects a 100 μA load to the battery selected by
TEMP_BSEL .
v2
55
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
71M6545-IGT/F
IC ENERGY METERING
720-10007-00300
CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025
CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300
CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300
CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881
8 POS T/P SHLD 4 GR ASSY
7250B
PANEL KIT BOTTOM FOR R-1220 CASE
731-10061-00200
CBL DSUB HD 15FEMAL-15MALE 2.0M
相关代理商/技术参数
71M6543F-IGTR/F
功能描述:计量片上系统 - SoC Precision Energy Meter IC
RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6543FT-IGT/F
制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube
71M6543FT-IGTR/F
制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6543G
制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
71M6543GH
制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC
71M6543GHT-IGT/F
制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk
71M6543GHT-IGTR/F
制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Tape and Reel
71M6543G-IGT/F
功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel